HANGKAI 12 hp Outboard Motor Long Shaft, 169CC 2 Stroke Outboard Motor With CDI Ignition Water Cooling System Fishing Boat Engine With Fuel Tank (12 HP Long Shaft+tank)

Details:Three-blade Propeller: The three-blades propeller with a streamlined design provides you with greater power.Silencer Cover: The silencer cover can absorb the noise generated by the fan through the internal sound-absorbing material, thus providing a quieter working environment.Anti-swirl Plate: The anti-swirl plate can effectively reduce the turbulence of the waves and avoid water-wetting clothes.Application:This outboard motor is suitable for small ships with different materials(width less than 4.9 feet and length less than 19.7 inches), such as inflatable boats, iron boats, plastic boats, fiberglass boats, and wooden boats. It is widely used in fishery, aquaculture, outdoor exploration, etc.Gear Oil Filling Method:There is a screw on the gearbox, unscrew the screw to add gear oil. Each machine will be filled with gear oil before leaving the factory, so it does not need to be refilled when it is used for the first time. After that, add according to personal use, and check every ten hours.Specification:Material: Aluminum AlloyColor: BlackModel: 12HP Horsepower Long AxisDisplacement: 169CCGear Ratio: 2.08 (27:13)Number of Cylinders: 2Speed: 4500-5500RPMGear: F-N-RRefueling Method: 92 Unleaded Gasoline is RecommendedMaximum Power: 8.8kwOil Tank Capacity: 24L/6.34galEndurance: 5-6hMax. Load-bearing Capacity: 1000kg/2204lbsIgnition System: CDICooling System: Water CoolingControl System: Tiller ControlStart System: Manual StartSuitable Stern Plate Height: 45cm-55cm/17.7*21.7inPropeller Specification: 23.5cm/9.25in (Length) * 20.3cm/8in (Diameter)Cylinder Diameter * Stroke: 50mm/2in * 43mm/1.7inRecommended Engine Oil: 2 Stroke Engine OilMixing Ratio: Fuel: Oil = 50:1Trim and Tilt System: Manual TiltNet Weight: 32kg/70.5lbsProduct Size: 87.3*33.2*104cm/34.4*13.1*40.9inPackage Included:1x Outboard Motor1x Flameout Rope1x Oil Pipe1x Sealing Ring1x Paper Pad1x Spark Plug1x Start Rope1x Water Pump Impeller1x Cotter Pin1x Fuel Tank1x English ManualOther ToolsNotes:1. The two-stroke outboard must use a mixture of No. 92 gasoline and two-stroke engine oil.2. The volume ratio of gasoline and oil during the running-in period of the new machine is 25:1.3. After the running-in period, the volume ratio of gasoline and oil is 50:1.4. Special attention: gasoline and engine oil must be pre-mixed and stirred evenly, and then poured into the fuel tank.5. The outboard motor must be started in water, do not start the engine on shore.6. Loosen the vent screw on the fuel tank cover counterclockwise when starting.7. When the outboard motor is started, the emergency flameout rope should be inserted, and the other end should be placed on the wrist or belt.8. The running-in period is about 10 hours or a month, and during the running-in period, do not drive with a high accelerator.9. Replace the gear oil after the running-in period, and the second replacement time is after 100 hours or about six months.10. Two-stroke air-cooled engines must use TCW-2 engine oil, which must be specifically designed for outboard engines.11. Fuel mixture ratio: 25:1 for the first 50 hours, 50:1 after 50 hours.12. Two-stroke outboard engines must use a mixture of 92# gasoline and two-stroke engine oil.13. During the break-in period, the volume ratio of gasoline to oil is 25:1. 14. After the break-in period, the volume ratio of gasoline to oil is 50:1.15. Important note: Gasoline and oil must be pre-mixed and thoroughly stirred before being poured into the fuel tank. 16. The outboard motor must be started in water, please do not start the engine on land.17. When starting the engine, loosen the vent screw on the fuel tank cap counterclockwise.18. When starting the outboard motor, insert the emergency stop rope and secure the other end to your wrist or belt.19. The break-in period lasts approximately 10 hours or one month. Please avoid operating the engine at high throttle during the break-in period.20. After the break-in period, replace the gear oil. The second replacement should be performed after approximately 100 hours or six months.

• ★STRONG POWER★ 2-stroke 12hp engine (4500 to 5500rpm) and 8.8kw max. power provide strong power for you to drive fast and save a lot of time and energy.
• ★EXCELLENT LOAD-BEARING CAPACITY★ With solid aluminum alloy material and a powerful engine, the outboard engine has a maximum load of 2204 pounds to meet different needs. (The heavier the load, the slower the speed)
• ★EXCELLENT ENDURANCE★ Low fuel consumption, efficient two-stroke motor, and large capacity fuel tank (6.34 gallons) provide you with 5-6 hours of endurance to meet the needs of short/long distance travel.
• ★EXCELLENT HEAT DISSIPATION★ Its water cooling system helps to cool the motor and has better performance. The design of the vent can also extend its service life.
• ★PREMIUM MATERIAL★ This 2-stroke 12hp engine is made of high-quality aluminium, which is fracture-resistant, acid resistance, and not easy to deform, making it suitable for use in water.