Bob Smith Industries Cyanoacrylate Bundle, Super Thin Insta-Cure, Gap Filling Medium Insta-Cure+, Extra Thick Maxi-Cure, and Accelerator Insta-Set (Pack of 4) - Bundled with Make Your Day Paintbrushes

Bob Smith Industries Cyanoacrylate Bundle, Super Thin Insta-Cure, Gap Filling Medium Insta-Cure+, Extra Thick Maxi-Cure, and Accelerator Insta-Set (Pack of 4) - Bundled with Make Your Day PaintbrushesIncludes One of Each Item, Insta-Cure 3/4 oz (BSI131), Insta-Cure+ 3/4 oz (BSI133), Maxi-Cure 3/4 oz (BSI135), Insta-Set 2oz (BSI151), and MYD PaintbrushesInsta-Cure has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.Insta-Cure+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.Maxi-Cure extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars.INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET activates CA in 6 to 8 seconds and is compatible with all surfaces, even clear plastic and white foam.Make Your Day Paintbrushes - Achieve precision and creativity with our 10-piece paintbrush set, offering a variety of sizes for all your artistic needs.

• Includes One of Each Item, Insta-Cure 3/4 oz (BSI131), Insta-Cure+ 3/4 oz (BSI133), Maxi-Cure 3/4 oz (BSI135), Insta-Set 2oz (BSI151), and MYD Paintbrushes
• Insta-Cure has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.
• Insta-Cure+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.
• Maxi-Cure extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars.
• INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET activates CA in 6 to 8 seconds and is compatible with all surfaces, even clear plastic and white foam.
• Make Your Day Paintbrushes - Achieve precision and creativity with our 10-piece paintbrush set, offering a variety of sizes for all your artistic needs.